Відео

THANKS FOR THE INFO GOOD VIDEO

I GOT A BADBOY MYSELF AND THEY BAD FOR SURE ITS A BEAST

I WANTED TO SEE IT CUT SOME GRASS LOL

What height are you cutting at?

Excellent video. Thanks for taking the time to make it. Much Appreciated!

I really enjoy your videos. My favorite push mower is a Lawnboy 21" with a magnesium deck from the 1980s. It has offset wheels making turns easier and better edging. It will also bag grass perfectly. I have had mine since 1985. What you do is find a Lawnboy mower for its deck. Then you place a briggs and stratton engine on it. Now you have the best push mower in the world with little cost that will last a lifetime. I would send you a picture of mine, but I don't know how to do that. Good luck and keep up the great videos.

I just did my initial oil change, 9.3 hours and thanks to your video, it went without a hiccup. KUDOS!!

What push mower is that

I had to buy a new battery for my John Deere mower because the old one tested bad and was 5 years old. After connecting the new battery, I put a new one of these tenders on it. It immediately went to "solid red". Should the new battery really need charging? I use the battery cable claps to connect it. Thanks

Hey man Rodney here..Where did you get your mower ramps? I need a set..Thanks

You should move your drain bucket when putting new filters on. P.S work smarter not harder. 👍😁👍

Gold blades overrated

Very nicely done.

Watched it one time. Did job on my mower. Turned out great. Thanks.

Why does everyone's deck always look less rusty and more clean than mine?? LoL

Looks like it from build up under deck. I been running the gold blades on 2 of my 3 mowers without anything like this. They have been great

It's a constant problem with me. Maverick HD 54' deck. Purchased new at the end of the season last year and have already destroyed two sets of blades. Four acres of sandy turf. I always try to mow just after it rains and it helps. It has not been just with this mower and blades. All the previous mowers have produced the same result. I did use a finish mower (Rhino TM60) and would run it at a lower RPM and that would prolong the life of the blades. I have not found a blade that will last more than 4 cuttings with the Maverick HD. The good news it I never worry about grass accumulating under the deck. The inside of my deck is always clean.

Wish you could show a video of taking the deck off a bad boy maverick. Thanks

😮

I have a question to see if you can answer it. I have a bad boy Mavic and my steering arms one of them works real good. The other one doesn’t react as well. I don’t know if it’s a linkage or if it needs to be greased up so when I go in reverse, I believe it’s the right side I have to pull it twice as far back for it to work, the problem is I don’t know what the problem is. Everything seems to be OK.

How did the paint hold up 2yrs later?

The best part of the job, the most fun for me, on the first attempt, was getting the blade, washers, and axis lock back together. I have the method now 😅

Like the other guy said, check your service manual. My bad boy is supposed to be 1/4 inch higher in the rear of the deck than the front. Gauge your deck height off the front, then raise the rear by 1/4" is what mine said to do.

Can I get a good view of the throttle linkage springs

Just found your channel, new Bad Boy Maverick owner (guess that makes me a Bad Girl). Apologies if you covered this before, any ideas on how to fix the little mohawks left behind by BB? Other owners complain about this. Upgrade pulleys, speed?

I have a ZT Elite and did the same this. Brush to 4' and Saplings to about 2". I ALMOST bought a Brush Hog, but Sharpened Blades and had at it.. Thanks for the Video

Good video 👍

12lbs, may try 10 how many hours are you gonna run your Hydraulic fluid and filters?

Which engine is this?

This video saved my bacon! Thanks! I replaced my clutch, and after everything was put together and bolted up with Loctight, I realized I put the clutch on 180* off, meaning the electrical connection was on the opposite side of where it should be. I was ready to pull the clutch and start all over, then I did a quick search on loosening the drive belt and found this video! Took me about 10 minutes to loosen the drive belt tensioner a no spin the clutch. Thanks again.

What side rich did you use to take the blade off

Maybe try to not getting it held in place by the wood.

100hr? I had that almost within a month of ownership 🤣 I've been running bad boys since they came out. The one I use right now just turned six years old the middle of May. When I stepped off the machine yesterday it had 2864 hours on it almost 3000 hours, front yard and backyard that averages about 6.7 acres not to mention the additional 5 1/2 to 6 acres up at Meyer and Hanger So every time I mow is about 13 acres I can mow it all in roughly 1 hour and 45 minutes. Then I loaded up and go mow my daddy's place which is about 2 1/2 acres and then I drive down the road and do the camp house which is another 2 acres. And living here in East Texas mowing season starts generally around the end of February or first of March and goes all the way just about until Christmas The bad outlaw XP that I have has a 38 fuel injected rig with a 72 inch cut and not a single dime has been spent in repairs on this machine just blades and belts and believe it or not I have not changed a single spindle on the deck. No I'm not saying it isn't wore out or like brand new but it's still running like a champ I went to purchase one brand new last week but could not find one in the entire state of Texas that was a 72 inch cut with a fuel injected Briggs they all had the junky kohlers.

😘

Do you ever adjust the deck belt tension on deck? If so do you have a video? Seems my belt keeps getting loose and deck belt not as tight as should be

ok so you bought the pipes already threaded and all you did was use a hack saw to make shorter ones ? ....did they not have the shorter pipes you needed ?.....ya lost me on this one bro lowes and most stores that sell the black pipe offer diff lengths and then all ya do is screw the clamps on and not worry bout cutting them. Another person commented that the clamps they bought would slide off when useing them and it was because they didn't have the pipe clamp end with the handle in screwed into the threads (the pipe has to have 1 end with threads or else they wont work ).....Boggle/smh ... i know some people dont watch and listen

What you need is Circular Saw Blade - Chisel Tooth It very very nice!

Are you blazing a trail in there? Or just clearing space

hummm, i think that is not the correct set for the type bush/plants!!! For that u could use the nylon for the grass and the Disc for trees and sticks!

This was painful to watch. Crooked snake lines. Blowing grass into mulch bed. Pivot spins instead of 3 points. That was rough

Do u adjust tension on the deck belt same as u did on the drive belt thanks

You should make sure your voice is recorded. I couldn't hear anything your said while going over the blade. Yes, the computer and video sound settings were turned up the loudest they would go.

damn the music

How did you start it without having to sit on seat

I’m going to be your next video’s sponsor.

South Mississippi check in! how are you liking the bad boy maverick? im debating the zt elite for my 3 acres just north of hattiesburg.

Looks like you made all sides of deck same height. But I just bought a Maverick Hd and my owners manual says front of deck should be 1/4 lower than back of deck. 🤷🏼‍♂️

Thanks.

Excellent video. Thank you.

Thanks . Great review. Looking at the HD model Koehler also. Service your machine